The traditional solar street light controllers one-sidedly emphasize the heat collection performance and emissivity, while ignoring the consideration of heat transfer speed, resulting in the hot water in the vacuum tube cannot be quickly transferred to the water tank, so the temperature rises slowly. The key to heat preservation is the foaming process of the heat preservation material and the thickness of the heat preservation layer. The heat preservation material must be integrally foamed with imported polyurethane and cured. Only in this way can the cells be small and uniform. Although some manufacturers use imported polyurethane, they are not foamed as a whole or have not undergone curing treatment, resulting in gaps in the insulation layer, just like wearing a cotton jacket in winter without buttons, and the insulation effect is not ideal. Secondly, the thicker the insulation layer, the higher the cell closure rate, the better the insulation effect, the more imported polyurethane is consumed, and the higher the cost. Manufacturers provide corresponding auxiliary configurations based on product performance, so that when auxiliary devices are used in combination with products, they can maximize performance without generating waste. Therefore, it is best to recognize whether it is with the solar energy host trademark when purchasing. Unanimous. At present, the mainstream charging technology in the market has three technologies: switching, PWM, and MPPT. Which charging technology is used directly determines the quality and cost of the controller. MPPT street light controller is better than PWM, and PWM is better than switching. Because in the construction site, there are often ordinary workers who do not know the use and characteristics of the product very well, so it is best to have the wiring diagram of the silk-printed street light controller on the shell of the controller we choose, and it is easy to install and clearly marked. The setup is simple and easy to understand. If the installation and settings are too cumbersome, it may cause the system to work abnormally. At this time, if someone comes to complain about your controller problem, it is a bit wronged.

When the charging voltage of the solar controller is higher than the protection voltage, it will automatically shut down to charge the battery. After that, when the voltage drops to the maintenance voltage, the battery will enter the floating charge state. When the voltage is lower than the recovery voltage, the float charge will be turned off and enter the equal charge state. When the battery voltage is lower than the protection voltage, the controller automatically turns off the output to protect the battery from damage; when the battery is recharged, it can automatically restore power. In order to launch new products and occupy the market as soon as possible, many street lamp manufacturers often launch the market before the products are fully mature. They have not done some complete tests at all. Such solar controllers will inevitably have many technical problems. Therefore, we need to understand the company's product information when choosing a solar controller to analyze the maturity of its product technology. The charging mode of the conventional solar controller is to copy the three-stage charging method of the mains charger, namely the three stages of constant current, constant voltage, and floating charge. If the current generated by the battery panel is greater than the current limited by the controller, it will cause a drop in charging efficiency. The MCT charging method is to track the current of the battery board without causing waste. By detecting the voltage of the battery and calculating the temperature compensation value, when the voltage of the battery is close to the peak value, the pulse-type trickle charging method is adopted, which can make the battery fully and also fully charged. Prevent the battery from overcharging. Coastal users can realize that a non-waterproof controller may corrode the circuit board in about half a year. In order to facilitate maintenance, most customers put the controller on the base of the light pole. However, many light pole manufacturers have poor airtightness of the base. When it rains, rainwater will enter, so the controller that is not completely waterproof is very useful. It may be corroded due to water entering. When the amount of rainwater entering is large, the controller circuit will be short-circuited in an instant.

Solar Street Light/Garden Light/Solar Flood Light/AC Street Light/Small System

Zhongshan Pude Lighting Technology Co., Ltd.

Zhongshan Pude Lighting Technology Co., Ltd. is currently one of the large-scale professional street lighting manufacturers in China, and the preferred supplier for many road lighting and new rural lighting projects. Main products: solar street lights, solar flood lights, stadium lights, landscape lights, courtyard lights, lawn lights, column head lights, wall lights and more than 1,000 design products. If you need more information about solar lights, please contact us.